AutosTalk Forums  

rover 200 brake lights

Cars Maintenance General car maintenance (uk.rec.cars.maintenance)


Discuss rover 200 brake lights in the Cars Maintenance forum.



Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old   
Ruth33
 
Posts: n/a

Default rover 200 brake lights - 04-20-2007 , 09:00 PM







Hi everyone,

I have a slight problem if anyone could help, I have a rover 200 and
when I turn on the engine the brake lights come on and remain on until
the engine is switched off, pressing the brake peddle makes no
difference. Everything else works (at the moment).
So if there are any budding helpers out there who could give me some
advice before I spend out on a garage job, for something that may just
be really simple, I would be really gratefull.

Thanks guys

Ruth33




--
Ruth33

Reply With Quote
  #2  
Old   
Rob graham
 
Posts: n/a

Default Re: rover 200 brake lights - 04-21-2007 , 01:57 AM







"Ruth33" <Ruth33.2pdh3n (AT) autobanter (DOT) co.uk> wrote

Quote:
Hi everyone,

I have a slight problem if anyone could help, I have a rover 200 and
when I turn on the engine the brake lights come on and remain on until
the engine is switched off, pressing the brake peddle makes no
difference. Everything else works (at the moment).
So if there are any budding helpers out there who could give me some
advice before I spend out on a garage job, for something that may just
be really simple, I would be really gratefull.

Thanks guys

Ruth33

It sounds very much as though the brake light switch has got stuck on and
needs to be replaced. Unfortunately, I don't know for certain where it is
positioned but I would look near the pedal and see if it was there. It
probably is (you'll have to bend down and look under where the pedal is
mounted). Disconnected the wire from the switch and if the light goes out
then it's pretty certain to be the switch.

Rob Graham




Reply With Quote
  #3  
Old   
MrCheerful
 
Posts: n/a

Default Re: rover 200 brake lights - 04-21-2007 , 02:21 AM




"Ruth33" <Ruth33.2pdh3n (AT) autobanter (DOT) co.uk> wrote

Quote:
Hi everyone,

I have a slight problem if anyone could help, I have a rover 200 and
when I turn on the engine the brake lights come on and remain on until
the engine is switched off, pressing the brake peddle makes no
difference. Everything else works (at the moment).
So if there are any budding helpers out there who could give me some
advice before I spend out on a garage job, for something that may just
be really simple, I would be really gratefull.

Thanks guys

Ruth33
The brake light switch is the fault (in all probability) It may (probably)
only need adjustment, or it may need replacement.

The switch is directly operated by the pedal being pushed away from it , so
move the seat back and get your head near the pedals and look up, remove any
trim that may be in the way, the switch is a little black thing with two
wires going to it immediately above the brake pedal. Usually the switch is
adjustable by means of the thread on the outside of it, mostly a quarter
turn anticlockwise unlocks the switch which can then be moved down toward
the pedal to turn the brake lights off. a quarter turn clockwise will
relock the switch, check adjustment in use, ie gentle braking puts the brake
lights on.

The switch can become maladjusted by accidentally pulling the brake pedal
up, especially by those old Krooklock devices that lock the pedal to the
steering wheel.

Mrcheerful




Reply With Quote
  #4  
Old   
Paul Hubbard
 
Posts: n/a

Default Re: rover 200 brake lights - 04-21-2007 , 04:18 AM




"MrCheerful" <nbkm57 (AT) hotmail (DOT) com> wrote

Quote:
The switch is directly operated by the pedal being pushed away from it ,
so move the seat back and get your head near the pedals and look up,
remove any trim that may be in the way, the switch is a little black thing
with two wires going to it immediately above the brake pedal. Usually the
switch is adjustable by means of the thread on the outside of it, mostly a
quarter turn anticlockwise unlocks the switch which can then be moved down
toward the pedal to turn the brake lights off. a quarter turn clockwise
will relock the switch, check adjustment in use, ie gentle braking puts
the brake lights on.
It usually has a feed to the ecu to cut fuelling when braking, has she been
surging when braking?

PDH




Reply With Quote
Reply




Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.