AutosTalk Forums  

1995 Nissan Maxima SE Manual Transmission

Nissan Maxima Discussion of the Nissan Maxima Automobile (alt.autos.nissan.maxima)


Discuss 1995 Nissan Maxima SE Manual Transmission in the Nissan Maxima forum.



Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old   
Doug Ritschel
 
Posts: n/a

Default 1995 Nissan Maxima SE Manual Transmission - 03-15-2007 , 09:58 PM






I have a 1995 Nissan Maxima SE with a manual transmission. The clutch first
went at 90K miles. After getting it replaced by Nissan, it would slip every
once in a while. At about 140K miles I decided to get the clutch replaced,
since the first one gave no warning at all. Now it has 178K on it and the
clutch went again. I'm trying to decide if it is worth replacing. The car
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced and troubleshooting to
determine why there is a draw on the battery when the car is off, and why it
stalls until warmed up.

The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.





Reply With Quote
  #2  
Old   
David Geesaman
 
Posts: n/a

Default Re: 1995 Nissan Maxima SE Manual Transmission - 03-15-2007 , 10:24 PM






Doug Ritschel wrote:
Quote:
I have a 1995 Nissan Maxima SE with a manual transmission. The clutch first
went at 90K miles. After getting it replaced by Nissan, it would slip every
once in a while. At about 140K miles I decided to get the clutch replaced,
since the first one gave no warning at all. Now it has 178K on it and the
clutch went again. I'm trying to decide if it is worth replacing. The car
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced and troubleshooting to
determine why there is a draw on the battery when the car is off, and why it
stalls until warmed up.

The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.
If you keep it, get some driving instruction. Unless you take this car
to the drag strip, there is no reason for 3 clutches in 200k.

Dave


Reply With Quote
  #3  
Old   
Codifus
 
Posts: n/a

Default Re: 1995 Nissan Maxima SE Manual Transmission - 03-15-2007 , 10:29 PM



Doug Ritschel wrote:
Quote:
I have a 1995 Nissan Maxima SE with a manual transmission. The clutch first
went at 90K miles. After getting it replaced by Nissan, it would slip every
once in a while. At about 140K miles I decided to get the clutch replaced,
since the first one gave no warning at all. Now it has 178K on it and the
clutch went again. I'm trying to decide if it is worth replacing.
Keep it and replace the clutch. It seems to consistantly go every 90K
miles. Clutch wear is dependant on so many things, most influential
being the driver's habits. Since your clutch wear seems consistent, it
looks like the system is OK.

That maxima can go about 300K miles with good care. You're about half
way through with it.

The car
Quote:
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced
Replace the starter yourself, it's a very easy job. OR, re-lubricate it.
Look here;

http://www.motorvate.ca/mvp.php

I used his well detailed site to re-lube my starter when it was acting up.


and troubleshooting to
Quote:
determine why there is a draw on the battery when the car is off
Possibly bad grounding somewhere? It's an old car and all the ground
points have oxidized significanlty. Check things like;
The -ve battery cable, it leads to a thick cable that attaches to the
metal tranny housing.
Alternator connections, but since the ALT has been replaced, the
connections may have been cleaned up somewhat.

You can even add a ground kit. Google it up.

and why it
Quote:
stalls until warmed up.
For the stalls,clean your throttle body and make sure to use cleaner
that's safe for fuel injected engines. Do not use carbuerator cleaner.
It's an easy DIY job which involves removing all the plumbing associated
with the air filter housing. With the throttle body exposed you spray
the cleaner and wipe untill all the carbon deposits are gone. Use a
plastic toothbrush you're about to throw away.
Quote:
The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.
Keep it



Oh and, if you haven't done so already, I would recommend you change
your anti-freeze. Spend a little extra and use Nissan OEM fluid. Why?
The water pump replacement job on a 4th gen Maxima is expensive, about
$400 or more, and you really shouldn't DIY on that one.

Hope this helps

CD

Quote:




Reply With Quote
  #4  
Old   
Doug Ritschel
 
Posts: n/a

Default Re: 1995 Nissan Maxima SE Manual Transmission - 03-15-2007 , 11:08 PM




"David Geesaman" <dgeesamanIHateSpam (AT) yahoo (DOT) com> wrote

Quote:
Doug Ritschel wrote:
I have a 1995 Nissan Maxima SE with a manual transmission. The clutch
first
went at 90K miles. After getting it replaced by Nissan, it would slip
every
once in a while. At about 140K miles I decided to get the clutch
replaced,
since the first one gave no warning at all. Now it has 178K on it and
the
clutch went again. I'm trying to decide if it is worth replacing. The
car
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced and
troubleshooting to
determine why there is a draw on the battery when the car is off, and
why it
stalls until warmed up.

The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.

If you keep it, get some driving instruction. Unless you take this car
to the drag strip, there is no reason for 3 clutches in 200k.

Dave
I've driven manuals for the last 26 years. My first car was a 72 Corolla
that I bought in 1979, not sure how many miles were on it since the odometer
was broken. It gave fair warning, slowly slipping more and more until I had
it replaced. I put at least 70,000 miles on it without another problem.

Put 70,000 miles on the above Corolla.
Put about 90,000 miles on a 1978 Corolla.
Put about 50,000 miles on a Nissan Pickup.
Put around 90,000 miles on a Celica. Never had a problem.
Put around 90,000 miles on a Accord. Never had a problem.
Put around 90,000 miles on Maxima, before having any problems.
Put about 50,000 miles on a Nissan Pickup.


With the Maxima, I had taken it to Nissan for a tune up or oil change around
90,000 miles. They told me that it was hard to put in gear and that I needed
the clutch replaced. A few days later, I heard a loud noise and I could move
the shifter into any gear with pusing in the clutch. About a week after they
replaced it, I was driving around in a mountainous area and it started
slipping. Over the next 40,000 miles I noticed it slipping every once in a
while going up steep hills. I took it to a private mechanic for the third
clutch which lasted 38,000 miles. During the short lifetime of the second
and third clutch I lent the car out a lot, so there were drivers other than
myself.




Reply With Quote
  #5  
Old   
Mike
 
Posts: n/a

Default Re: 1995 Nissan Maxima SE Manual Transmission - 03-16-2007 , 07:48 PM



On Thu, 15 Mar 2007 20:58:04 -0500, "Doug Ritschel"
<ritschel (AT) optonline (DOT) net> wrote:

Quote:
I have a 1995 Nissan Maxima SE with a manual transmission. The clutch first
went at 90K miles. After getting it replaced by Nissan, it would slip every
once in a while. At about 140K miles I decided to get the clutch replaced,
since the first one gave no warning at all. Now it has 178K on it and the
clutch went again. I'm trying to decide if it is worth replacing. The car
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced and troubleshooting to
determine why there is a draw on the battery when the car is off, and why it
stalls until warmed up.

The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.



So where do yo get an oil pressure gauge in your 95 SE? My 96 SE
doesn't have one? Did I get cheated?

On a more serious note, my opinion is that Maxima clutches (at least
in my 89 and this 96) aren't the greatest. Mine has always made a
little "moan" at engagement at low engine speeds in 1st, and never has
a real positive feel at engagement. I drive like a little old lady
but my intuition is that a couple trips to the dragstrip and that
clutch would be done. Same feeling with my 89...although it went to
the end (about 300K) without a replacement.

My other car, a Miata of the same year, has a much more positive
clutch feel on engagement.

I wondering if some of our faster contributors might have some
suggestions on beefier replacement clutches/pressure plates (or maybe
oil pressure gauges )

M


Reply With Quote
  #6  
Old   
David Geesaman
 
Posts: n/a

Default Re: 1995 Nissan Maxima SE Manual Transmission - 03-16-2007 , 08:51 PM



Doug Ritschel wrote:
Quote:
"David Geesaman" <dgeesamanIHateSpam (AT) yahoo (DOT) com> wrote in message
news:etcv5h02754 (AT) news2 (DOT) newsguy.com...
Doug Ritschel wrote:
I have a 1995 Nissan Maxima SE with a manual transmission. The clutch
first
went at 90K miles. After getting it replaced by Nissan, it would slip
every
once in a while. At about 140K miles I decided to get the clutch
replaced,
since the first one gave no warning at all. Now it has 178K on it and
the
clutch went again. I'm trying to decide if it is worth replacing. The
car
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced and
troubleshooting to
determine why there is a draw on the battery when the car is off, and
why it
stalls until warmed up.

The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.
If you keep it, get some driving instruction. Unless you take this car
to the drag strip, there is no reason for 3 clutches in 200k.

Dave

I've driven manuals for the last 26 years. My first car was a 72 Corolla
that I bought in 1979, not sure how many miles were on it since the odometer
was broken. It gave fair warning, slowly slipping more and more until I had
it replaced. I put at least 70,000 miles on it without another problem.

Put 70,000 miles on the above Corolla.
Put about 90,000 miles on a 1978 Corolla.
Put about 50,000 miles on a Nissan Pickup.
Put around 90,000 miles on a Celica. Never had a problem.
Put around 90,000 miles on a Accord. Never had a problem.
Put around 90,000 miles on Maxima, before having any problems.
Put about 50,000 miles on a Nissan Pickup.


With the Maxima, I had taken it to Nissan for a tune up or oil change around
90,000 miles. They told me that it was hard to put in gear and that I needed
the clutch replaced. A few days later, I heard a loud noise and I could move
the shifter into any gear with pusing in the clutch. About a week after they
replaced it, I was driving around in a mountainous area and it started
slipping. Over the next 40,000 miles I noticed it slipping every once in a
while going up steep hills. I took it to a private mechanic for the third
clutch which lasted 38,000 miles. During the short lifetime of the second
and third clutch I lent the car out a lot, so there were drivers other than
myself.
Yeah, that sounds more reasonable. But I would also change the clutch
and keep truckin.

Dave


Reply With Quote
  #7  
Old   
Doug Ritschel
 
Posts: n/a

Default Re: 1995 Nissan Maxima SE Manual Transmission - 03-16-2007 , 10:03 PM




"Mike" <notlikely (AT) mail (DOT) com> wrote

Quote:
On Thu, 15 Mar 2007 20:58:04 -0500, "Doug Ritschel"
ritschel (AT) optonline (DOT) net> wrote:

I have a 1995 Nissan Maxima SE with a manual transmission. The clutch
first
went at 90K miles. After getting it replaced by Nissan, it would slip
every
once in a while. At about 140K miles I decided to get the clutch
replaced,
since the first one gave no warning at all. Now it has 178K on it and the
clutch went again. I'm trying to decide if it is worth replacing. The car
seems to be in pretty good shape, but I'm afraid to fix it and have
something else go. It also needs the starter replaced and troubleshooting
to
determine why there is a draw on the battery when the car is off, and why
it
stalls until warmed up.

The only things aside from brakes, clutches and tires that have been
replaced so far are:
Starter
Alternator
Rear Calipers
Oil preasure gauge
ignition switch

Any advice on whether to keep or get rid of it would be appreciated.




So where do yo get an oil pressure gauge in your 95 SE? My 96 SE
doesn't have one? Did I get cheated?

On a more serious note, my opinion is that Maxima clutches (at least
in my 89 and this 96) aren't the greatest. Mine has always made a
little "moan" at engagement at low engine speeds in 1st, and never has
a real positive feel at engagement. I drive like a little old lady
but my intuition is that a couple trips to the dragstrip and that
clutch would be done. Same feeling with my 89...although it went to
the end (about 300K) without a replacement.

My other car, a Miata of the same year, has a much more positive
clutch feel on engagement.

I wondering if some of our faster contributors might have some
suggestions on beefier replacement clutches/pressure plates (or maybe
oil pressure gauges )

M
Did I say gauge? I meant switch.
This is what is on the bill:
""Tech noted oil preasure switch leaking
Story tech found and replaced leaking oil preasure switch"
Part $15.00.
Labor $40.00.





Reply With Quote
Reply




Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.